Saeco Vienna Plus

Saeco Vienna Plus Repair Service Tips

Saeco Vienna Plus coffee machine is a great fully automatic machine and good choice for the perfect coffee fanatics.

This machine is intended for household use.

Max coffee per day: 10 cups

Manual & Documentation

★ Do you need spare parts? ★

We have a huge range of replacement parts for your Saeco Vienna Plus Coffee Maker.
Visit our online store here >

Guide to troubleshoot your Saeco Vienna Plus Coffee Machine



Electricity related issues

Not turning on

Cable and cable fuse

It is really rare for the fuse to go, but can happen in case of a shorted component.
Check the fuse in the plug. Make sure the plug is properly connected into the connector slot.
Cable and cable fuse

Door microswitch

In these models the door microswitch is located on a separate stand which can flip out of it's place.
Make sure the service door is properly closed and the flap pressing the door microswitch is not deformed.
Door microswitch

Inner fuse

In case of a power surge in the house the inner fuse is the most likely part to go.
Inner fuse

Thermostat(s)

Some thermostats need to be reactivated after a possible overheating of the machine, while they can also go in case of an extreme overheating issue.
Thermostat(s)

Electric panel

Mainly the transformer is the part that causes this symptom.
Electric panel
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Not heating up
Unfortunately all possible causes need the attention of a professional.

Thermostat(s)

Some thermostats need to be reactivated after a possible overheating of the machine, while they can also go in case of an extreme overheating issue.
Thermostat(s)

Temperature sensor

Although rarely, but the temperature sensor can cause this fault as well.
Temperature sensor

Electric panel

Ocasionally faulty triacs and varistors can cause such a symptom.
Electric panel
Burnt smell
Unfortunately all possible causes need the attention of a professional.

Electric components

Almost any electric component can cause burnt smell.

Electric board

Burnt smell mainly arises from faulty electric boards.
Electric board
Lights / error messages

Red flashing

The most common problem is spilled ground coffee under the brew unit and behind the drip tray, making it impossible to put them back correctly.
Check all removable components. One might not be correctly in place.
Red flashing

Red steady

If You forget to check the containers, it might happen that either the beans or the water runs empty.
Check the water and coffee bean containers and refill if necessary.
Red steady

Green slow flashing

Normally this is the sign of the machine heating and it should switch to steady after maximum 5 minutes.

Green steady on

The machine is ready for use in the selected mode (coffee or steam).

Green fast flashing

This mainly occurs after steaming with the machine, because the boiler needs to be cooled down to coffee temperature.
Let water through the steam wand to cool the machine down.
Green fast flashing
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.


Water related issues

Leaking

Dirty water

This problem is mainly caused by ground coffee piling up in the drainage vent, blocking the path of the excess water let out by the overpressure or the boiler valve.
Clean and lubricate brew unit.
Clean the drainage vent behind the brew unit thoroughly.
Dirty water

Clear water

This is a clear sign of a leaking water system. We strongly advise to stop operating the machine as soon as You come across with this fault.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Fill water tank

Warning light steady on after water tank ran out of water.

The described symptom happens because the water tank runs empty while the machine is still operating.
Fill the water tank and let water through the steam wand till you get a continuous flow.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
No water / coffee through the machine

Airlock

If the water tank ran out of water during operation, then it sucks air into the water system.
Fill the water tank and let water through the steam wand till you get a continuous flow.

Water working, but no coffee

In cases, where You can't get coffee out of the machine even though You get water through the steam wand, the most common cause is a blocked, dirty brew unit.
Clean and lubricate brew unit.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Not steaming

Frother blocked

You need to keep in mind, that all frothers need to be cleaned straight away after use, otherwise milk residue will build up and block the steam wand and frother.
Clean the frother attachment and steam wand.
Frother blocked
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.

Brew unit related issues

Brew unit blocked

Brew unit is clogged up

The brew unit is the heart of the machine and it is recommended to be cleaned once a week under running water.
Clean and lubricate brew unit.

Brew unit stuck

This mainly happens when the user tries to force the brew unit out without reseting it to neutral position.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Can't replace the brew unit

Gears are not aligned

This fault mainly occurs when the user removes the dump box of before the machine could reset itself to neutral position.
Put the brew unit aside and everything else back to their places, close the service door and turn the machine off and then on, wait till the machine stands completely still and you should be able to replace the brew unit.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Unusual noises from the brew unit

Clicking / cracking sound

Mostly a sound generated by the brew unit and it is a sign of the lack of lubrication.
Clean and lubricate brew unit.

Gearbox damaged

In extreme cases, the lack of lubrication can even lead to overexerting and damaging the gearbox.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Slow brew unit operation

Brew unit clogged up

The fault might simply originate from the lack of maintenance, caused by piled up ground coffee blocking the operation of the brew unit.
Clean and lubricate brew unit.

Electric board

A rather frequent issue with these machines is an electric board failure that causes the gearbox motor to operate slowly, thereby exceeding the timeframe of operation and resulting in a blocked brew unit symptom.
Electric board
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.

Ground coffee related issues

Puck consistence

Pucks are falling apart

The ground coffee can't stay together as a puck if it's too coarse or the quantity of ground coffee is too low.
Readjust the grinder to grind finer.
Set the ground coffee quantity higher.
Pucks are falling apart

Pucks are muddy

The puck becomes muddy if the ground coffee is too fine and water can't pass through it.
Readjust the grinder to grind coarser.
Set the ground coffee quantity higher.
Clear and lubricate brew unit.
Pucks are muddy
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Unused coffee in waste

Ocasionally

The ground coffee quantity is probably set too high.
Clean and lubricate brew unit.
Clean and readjust grinder.

Frequently

The ground coffee fineness is probably set too coarse and the brew unit can't compress it to a puck.
Clean and lubricate brew unit.
Clean and readjust grinder.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Water in dump box

Clean water

Clean water mostly gets in the dump box in larger quantities if the brew unit is not properly cleaned.
Clean and lubricate brew unit.

Coffee

In case coffee ends up in the dump box, that means the brew unit is damaged.

In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Spilled ground coffee

Small amount

All automatic machines spill some ground coffee around the brew unit. You need to clean and lubricate the brew unit on a regular basis to keep the machine running and clean.
Clean and lubricate brew unit.

Large amount

This maily occurs because of the brew unit as symptom of the lack of lubrication.
Clean and lubricate brew unit.
Clean and readjust grinder.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Not grinding coffee

Grinder operating, but not grinding the beans

In the vast majority of the cases this symptom is caused by either some kind of liquid that was poured into the grinder or greasy coffee beans. Both result in ground coffee stuck to the blades making them unable to grind the coffee.
Clean and readjust grinder.

Grinder does not operate

The grinder is either blocked by some foreign object or the motor might be worn out or faulty.
Clean and readjust grinder.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.

End product related issues

Coffee dripping

Brew unit clogged up

A possible problem is that the shower disc is blocked by coffee residue.
Clean and lubricate brew unit.

The ground coffee is too fine

The grinder fineness settings might be too fine and water can't pass through the ground coffee, or the ground coffee is so fine, that it can block the shower disc.
Readjust the grinder to grind coarser.
Set the ground coffee quantity lower.
The ground coffee is too fine
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Coffee is running through and comes out weak

The ground coffee is too coarse

This might happen if the blades are worn, but they can probably be redajusted.
Readjust the grinder to grind finer.
Set the ground coffee quantity higher.
The ground coffee is too coarse

Wrong beans

The beans might be stale or the percentage of arabica beans in the blend might be too high. For these machines we reccomend at least 40% robusta percentage.
Try different beans.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Coffee temperature

Too high

The temperature might be too high in case the system has a larger amount of limescale built up inside.
Descale the machine.

Lukewarm

Oddly enough in most cases this issue is not related to the machine at all. It is rather related to the cold mug or cup the user brews the coffee into.
Pre-heat the cup before brewing coffee.

Cold

This is a rare issue, mainly caused by a faulty temperature sensor.
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Coffee consistence

Weak

The strength of the coffee is influenced by the coffee blend, the ground coffee fineness and quantity, the temperature and the pressure. A weak coffee might be the result of stale beans or too high arabica percentage, coarse ground coffee, low ground coffee quantity, low temperature, or a combination of these.
Readjust the grinder to grind finer.
Set the ground coffee quantity higher.
Try different beans.
Weak

Strong or sour

The strength of the coffee is influenced by the coffee blend, the ground coffee fineness and quantity, the temperature and the pressure. A strong coffee might be the result of high robusta percentage, fine ground coffee, high ground coffee quantity, high temperature, or a combination of these.
Readjust the grinder to grind coarser.
Set the ground coffee quantity lower.
Try different beans.
Strong or sour

There is no crema on top

In the world of automatic machines the theme crema will be somewhat simplified because of the low number of factors the user can influence and the low precision value of these adjustments. Basically there are three adjustable factors that have the most influence on the crema in a correctly operating automatic machine. These three factors are the coffee beans, the grinding fineness and the ground coffee quantity. The higher robusta percentage, the finer the ground coffee and the higher the coffee quantity is, the thicker the crema will turn out to be.
Readjust the grinder to grind finer.
Set the ground coffee quantity higher.
Try different beans.
There is no crema on top
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.
Milk froth consistence

Milk warms up, but is not froted

If You have steam pressure, but the milk is not frothed, then the problem can only be with the frother device. The most common problem is that the frother is not perfectly clean. You need to make sure to keep the small hole on the side of the frother attachment clear.
Clean the frother attachment and steam wand.
Descale the machine.
Milk warms up, but is not froted
In case You can't or don't want to resolve the problem with the tips above, then the machine needs the attention of a professional.